The Vapers Den

Recent Posts

Pages: [1] 2 3 4 5 6 ... 10
1
Rebuildable Atomiser Discussions / Re: Vandy Vape Beserker MTL RTA
« Last post by FahKingNut on July 20, 2018, 08:39:37 PM »
I am not ignoring you, I am just having a tough time typing right now with all of the shaking.

I hope to reply soon.
2
Rebuildable Atomiser Discussions / Re: What NOW???
« Last post by Ian on July 20, 2018, 07:00:56 PM »
While your searching the Internet, have a look at the Proton mod by Innokin. I can highly recommend it. Its a beautiful small dual 18650 mod with a great screen. Its light but really well built(is it is Innokin after all!!). It's my new favourite mod and I even prefer it to my RX Gen3. It only seems to come as a kit with the Scion tank but have a look on Everzon and you should get it cheap enough.
3
Rebuildable Atomiser Discussions / Re: What NOW???
« Last post by FahKingNut on July 20, 2018, 03:37:18 PM »
Guess what?

I dropped the whole setup, mod and RTA, and then hours later noticed that I was missing the mouthpiece!!!

I've searched the entire house - nothing!

Now I need a couple of replacement mouthpieces and at least one set of O-rings for the outer part of the metal sleeve that the mouthpiece fits into.

Time to go searching.
4
Device Discussions / Re: innokin Kroma zenith
« Last post by caz on July 20, 2018, 09:44:13 AM »
hi terrier hope you are well   ;D
5
Rebuildable Atomiser Discussions / Re: What NOW???
« Last post by CYBORG on July 19, 2018, 07:25:40 PM »
Get that Prime found Rik, if you can build the 5 then you can build the Prime and then you won’t look back.
6
Rebuildable Atomiser Discussions / Re: What NOW???
« Last post by Darth Vaper on July 19, 2018, 06:49:18 PM »
All you gotta do is make one good Kanthal coil.... it will last for ages

Take a little care when removing the old cotton that you don't mess the spacing up on the coil. 
7
Rebuildable Atomiser Discussions / Re: What NOW???
« Last post by FahKingNut on July 19, 2018, 12:02:33 PM »
I loved those Beserkers.  *sniff*

I've got a Prime around here somewhere.  I stopped looking when I found the 5 'cause nothing else was working, just leaking everywhere.

I had done some searching on The Den before I started this thread and while I saw that everyone was VERY happy with the Prime, but I was quite upset with it mostly from the building aspect of the deck.

I've become a lot more proficient with my builds since then and a lot faster too.

I'll give the Prime another shot if I can find the damn thing.   LOL  The 5 has been doing quite good once I remembered to close the air flow BEFORE refilling the tank!

Thanks everyone!!!  I really appreciate the help!!!
8
Device Discussions / Re: innokin Kroma zenith
« Last post by vapingfool on July 19, 2018, 05:38:34 AM »
Your question is pretty much meaningless as written.

We have no idea what nicotine strength is in your amber leaf rolling tobacco. Further, there is no real way to compare the nicotine levels between smoking and vaping.

I assume you are planning on 10 ml of vaping juice.  Does the flavored juice have any nicotine in it already? Do you want to end up with 10 ml of juice or do you want to add nicotine base to 10 ml of juice?

 
9
Device Discussions / Re: innokin Kroma zenith
« Last post by terrier on July 18, 2018, 09:04:39 AM »
Thanks for the info anyone got a clue on this one

How much nic do I put in a 10ml mix to get about the same strength as say amber leaf rolling tobacco, will be using 54mg/ml raw nic
10
Atomiser Reviews / Re: FreeMax Mesh Pro Tank - The Best in Mesh
« Last post by Ian on July 18, 2018, 02:30:18 AM »
I'm putting together a list at the moment, so I'll add that to it. Cheers Bud  :)+1
Pages: [1] 2 3 4 5 6 ... 10

* Theme Select



Forum Default

Permanently