Author Topic: Vandy Vape Beserker MTL RTA (Read 7911 times)

FahKingNut · « **Reply #75 on:** January 05, 2018, 08:52:54 AM »

Three days, four refills, and not a single drop anywhere!!!

Found the fix!!! Ignore the top-fill and bottom fill it like the old attys!!!

caz · « **Reply #76 on:** January 06, 2018, 12:07:05 PM »

glad you found a fix, good job

FahKingNut · « **Reply #77 on:** January 13, 2018, 11:17:28 PM »

Still no leaks.

Take that old man Darth!!!!

vapingfool · « **Reply #78 on:** January 14, 2018, 10:10:58 AM »

Fantastic. You may have finally solved the problem.

FahKingNut · « **Reply #79 on:** January 14, 2018, 02:03:48 PM »

I read it on a message board that the lovely Caz posted, just a few posts in and there it was!

It's basically bottom filling it, then gently blowing through it while the tank is inverted = no more leaks!!!

Darth Vaper · « **Reply #80 on:** January 14, 2018, 08:46:16 PM »

Glad to hear you got it sorted out Rik.

FahKingNut · « **Reply #81 on:** January 14, 2018, 11:29:14 PM »

Thank you, sir!!!

caz · « **Reply #82 on:** January 15, 2018, 06:24:17 AM »

Glad i have some use

pleased its working properly for you now

Darth Vaper · « **Reply #83 on:** January 15, 2018, 04:32:05 PM »

LOL I did tell him to blow it out in a napkin... so I'm only half useful

I'm a failure... just a shell of a man..... and you all have a front row seat to my downward spiral...

My drinking is getting out of control .... I just downed an entire jar of moonshine in one go.......

It's the little one on the left

Pretty tasty.. but not as good as the one I make.

FahKingNut · « **Reply #84 on:** January 15, 2018, 07:37:11 PM »

They insisted that the atty remain inverted. I've done this each time, but never got anything out.

Don't dispair Darth, I'm certain if you work at it there will be something else you can fail at.

Darth Vaper · « **Reply #85 on:** January 15, 2018, 07:40:04 PM »

Thank you for the kind words of perspiration Rik

LOL you little stinker

FahKingNut · « **Reply #86 on:** April 22, 2018, 06:14:41 PM »

The first tank randomly leaks out the base, at the bottom. The second tank has never leaked. Just got around to rotating the first tank back in and there is no reason it should leak, the second one is great! I'll probably try to find another one in the near future. Just thought I'd update this with me trying to rotate the two.

Darth Vaper · « **Reply #87 on:** April 22, 2018, 09:03:33 PM »

Check all the O-rings in the leaker Rik.... only takes one out of place.

FahKingNut · « **Reply #88 on:** April 22, 2018, 10:02:46 PM »

Already did that Brother Darth! All checks are good. I think it's leaking at the bottom "press fit" area. Just can't figure why it does sometimes and doesn't other times???

Darth Vaper · « **Reply #89 on:** April 22, 2018, 10:14:25 PM »

The way the pressure builds up in some of these tanks when you close them up can cause some funky leak issues.

I never removed my top o-ring on the Prime... I just start the cap back on and flip it upside down to tighten the rest of the way... when done I keep it upside down and just open the liquid feed a little to release the pressure..... no leaks.

FahKingNut · « **Reply #90 on:** April 22, 2018, 11:05:12 PM »

This is a top fill tank, but filling from the bottom leaves like zero pressure. I even test the airflow up-side-down. This one tank passes all of the tests and inspections. I worked almost 20 years in Industrial Aerospace Inspection, using x-ray, ultrasonics, magnetic particle, and florescent penetrant to identify defects. My personal record was viaually spotting a crace that was 0.007 of an inch. This damn tank has no defects that I can find, it has to be inside that base, at the bottom. No trace of leak on the sides, always on the bottom.

Ian · « **Reply #91 on:** April 23, 2018, 01:01:43 AM »

Is the 510 screw adjustable. Try giving that a little tightening. Could do the trick. Don't over tighten though, they easily break.

FahKingNut · « **Reply #92 on:** April 23, 2018, 01:15:49 AM »

They're mostly brass, right? I'll give that a shot!

Ian · « **Reply #93 on:** April 23, 2018, 03:58:34 AM »

Quote from: FahKingNut on April 23, 2018, 01:15:49 AM

They're mostly brass, right? I'll give that a shot!

Just from looking at a few googled pictures, it seems like the 510 screw is two parts. Remove the outer screw and tighten the inner screw. Then screw back in the outer screw. Don't over do the other screw, they are small and fragile.

FahKingNut · « **Reply #94 on:** April 23, 2018, 05:47:54 AM »

I've gotta find my computer toolbox. Not sure where it is since the apartment is in shambles from us getting ready to move into the RV, then me getting real sick, and skipping the whole RV thing. There are boxes everywhere. Needle in a haystack time.

beyonder · « **Reply #95 on:** July 02, 2018, 07:14:09 PM »

I think my Berserker is sort of brokted.

Nah, its good and meshed up.

FahKingNut · « **Reply #96 on:** July 15, 2018, 08:26:48 PM »

I have finally given up on the Vandy Vape Beserker MTL RTA. I have 3 of them. The newest one I opened, built it, filled, vaped, and refilled and vaped it until I had to rebuild on it. Once rebuilt, other than welding, it just won't stop leaking. All 3 of them leak, exact same way, at the bottom, from the press-fit seam, and always after a rebuild. Vandy Vape will rot in hell on a festering pile of goat shit before they get another cent from me.

A turd is a turd is a turd is a turd.

Ian · « **Reply #97 on:** July 15, 2018, 09:16:06 PM »

99% of leaking in an RTA is usually because of wicking. Here's a few question Rik and maybe we can fix the issue.
1) Are you filling up(but not stuffing) the wicking channels. Unless there is a major fault, the juice is somehow getting past your cotton and getting into the airflow. If your using a small diameter coil, there will be less cotton to fill the juice channels.
2) Is the cotton hanging over or really close to the airflow under the coil. This is an issue with my Ammit 25. I have to make sure the cotton is nowhere near the airflow or it will leak.
3) Is the 510 on the bottom tight??. Try tightening the 510 but don't go crazy, some of these screws can break, then your fucked.

FahKingNut · « **Reply #98 on:** July 20, 2018, 08:39:37 PM »

I am not ignoring you, I am just having a tough time typing right now with all of the shaking.

I hope to reply soon.

News:

Author Topic: Vandy Vape Beserker MTL RTA (Read 7911 times)

Theme Select